Product Overview
DESCRIPTION
ClimoPlate ™ is available in two Grades, this product selection is for ClimoPlate SB - (Solvent Based)
Please click here for ClimoPlate WB (Water Based Membrane) *** UNDER CONSTRUCTION ***
ClimoPlate SB™ is a New Zealand manufactured Alkyd / Bitumen co-polymer, solvent / water emulsion based top coat paint developed primarily for New Zealand outdoor conditions.
ClimoPlate SB™ is specifically but not exclusively formulated to act as a high gloss top coat over bitumen based sealers and primers such as our GilsoFlex™ and FlexsoTar™ products. It is ideally suited for painting of exposed primed metal roofs and primed steel structures. It is compatible and suitable to be used on Decramastic and Coloursteel roofs.
ClimoPlate SB™ can also be used on other substrates like timber, plywood etc.
Climoplate top coat paints are the best roof paint NZ has.
Because of its disinfecting effect, it will retard the growth of moss or lichen.
Substrate surface preparation requirements are minimal although a primer coat is recommended.
Typically a roof requires one top coat paint only and One (1) Litre will cover approximately 4 to 8 Square Meters, depending on roof surface and substrate.
- 4ltr will cover approximately 16 to 32 Square Meters
- 10ltr will cover approximately 40 to 80 Square Meters
- 20ltr will cover approximately 80 to 160 Square Meters
ClimoPlate SB™ is intended primarily for surface application by brushing, rolling or airless spraying using a 515 spray nozzle tip.
A re-coat might be required after 6 to 10 years.
We do carry our own standard colour range but please ask via "eMail" if you would like us to match a specific colour for you, and we will advise.
Please note you can now select your preferred product packaging.
FEATURES
- ClimoPlate SB™ is a Bitumen/Alkyd co-polymer Top Coat paint suitable over bitumen based sealers, primers and coatings.
- ClimoPlate SB™ is a semi-flexible coating and will not break down due to distortion and movement, caused by weather exposure
- ClimoPlate SB™ is non-corrosive to metals and can be painted directly over bitumen based products, primed bare steel, primed galvanised, powder coated, or previously painted steel and primed concrete with minimum surface preparation requirements.
- ClimoPlate SB™ is suitable on metal and concrete tile roofs. It can also be used on concrete brick and block work, plywood and timber.
- Can be used on other structures to paint the surface
- Drinking water collected from roofs coated with ClimoPlate SB™ is safe to consume once the product is fully dry and cured.
TECHNICAL SPECS
For more detailed information please see our documents below.
Packaging: Available in 4, 10, 20 and 200 Litre containers. Metal open top paint pail and Metal drum with bungs.
For Use On: Suitable for use on any cement tile and corrugated steel roofs, Decramastic roofs, Butynol/Bitumen roofs, steel structures, timber, concrete brick and block work etc.
Surface Preparation: Ensure surface is dry, dust free and not contaminated (Remove Contamination, moss, mold and any old, loose and flaky paint and rust before coating)
Top Coat: This product is intended to be used as a Top Coat over a primer or a sealer coat like GilsoFlex, although it does depend on the application as ClimoPlate SB can also be used as a stand alone paint under certain conditions.
Colour: Please see our standard colour range selection. We can colour match a specific colour for you if required.
Before Applying: The paint should be thoroughly stirred for at least 5 mins.
Application: Brush, Roller, Spray (we supply a suitable spray thinner if required)
Coverage: Depends upon surface:
– Tile roofs typically 3 - 6 m2/litre.
– Corrugated metal roofs typically 4 - 8 m2/litre.
No of Coats: Generally only one coat required, a second coat can be applied dependent on the condition of the roof and the colour depth required.
Recoat Time: As soon as previous coat is touch dry (approximately 4 hours), an additional coat can be applied if required.
Drying Time: Generally allow 24 hours, depending on surface and ambient conditions for the paint to be touch dry. The paint will be fully set in a week.
Thinners: Not recommended, however for spraying please see our web-site for a suitable thinner.
Clean Up: Clean equipment using recommended thinner, kerosine or mineral turpentine.
Durability: Recoat after 6 summers if required. In harsh climatic areas a recoat might be required sooner.
Other:
– Contains volatile solvent, keep away from heat and open flame.
– Keep out of reach of children.
– Keep closed when not in use, avoid breathing vapour - ensure good air flow when applying.
– Stir very regularly during application to ensure consistency of product.
– Do not apply if surface temperature is below 8°C or above 35°C
Storage, Handling Safety: Please avoid extreme temperatures when storing (Below 5°C and above 40°C) as the product can gel if exposed to these extreme temperatures. The self-life is typically 7 months from the purchase date, if stored in ideal conditions. Refer to attached Material Safety Data Sheet (MSDS) also refer to attached “Health and Safety in the Surface Coating Industry” Brief 3, October 2007 as published by the Department of Labour.
PRODUCT DOCUMENTATION
These documents contain important information about:
- Material Safety Data
- General Information
- Application
- Storage
- Safe use
- First Aid
- Clean Up
- Warranty
- Available Packing Sizes
- and more information
Note: To view the following PDF documents, you will require some type of PDF-reader plugin on your system.
If you need an up-to-date plugin you can install Adobe's free PDF reader from here.
Documents:
Material Safety Data Sheet (MSDS)
“Health and Safety in the Surface Coating Industry” Brief 3, October 2007 as published by the Department of Labour.
